Thanks for supporting local! Our online shop is open & shipping orders. 

Search

Cables & Connectors

Electronics Components

Motors & Controllers

On Sale items!

Get Professional Support

BBC Micro:bit

Robotics

On sale items!

Announcement


Check out our latest news to find out more about events, opportunities and partnerships.

Esmes' Electronics


Esmes' Electronics is a simple introduction to using the micro:bit written by a year 5 student.

Troys' tutorials


Learn with Troy by asking for support and, he will post a tutorial here to benefit all of our visitors. Free advice!

Feature teacher


Be inspired by some of our favorite teachers using our products.

Get professional support


Contact us now to request your own tutorial or learning resource.

This section doesn’t currently include any content. Add content to this section using the sidebar.

Image caption appears here

Add your deal, information or promotional text

MM-0073

Servo Board

36 items left

CLICK ME TO DOWNLOAD THE INSTRUCTIONS FOR THE SERVO KIT FOR MICRO:BIT.

The MonkMakes Servo for micro:bit board provides a really easy way to attach up to three servomotors to a BBC micro:bit. The board requires a power supply or battery pack to provide 5 or 6V to the servomotors. It includes a voltage regulator that will supply 3V back to the micro:bit, so that you don’t have to power it separately.

If you have one of our Servo Kit for micro:bit products, then you will find more information about that here. This is where you will also finds a getting started guide for this board.

Features

  • Header pins for three servo motors
  • Up to 2A total can be supplied to the servo motors
  • Regulated 3V output to power your micro:bit
  • Polarity protection for the servomotors
  • Electrolytic reservoir capacitor for the servomotors
  • 1kΩ series resistors to the control signals to prevent accidental sort-circuits of the micro:bit’s output pins.
  • Orange LED to indicate that the Servo for micro:bit board has power.

Connections

The picture below shows a typical setup using the Servo for micro:bit board.

The following connections have been made:

  • 3 x servomotors plugged into header pins. These need to be the right way around, with the control signal (yellow or orange wire) to the left (pins marked c).
  • Alligator clip lead from GND on the micro:bit to GND on the Servo for micro:bit board.
  • Optional alligator clip lead from 3V on the micro:bit to 3V on the Servo for micro:bit board. You only need this if you want to power the micro:bit from the same battery pack as the servomotors. If you want to power the micro:bit over USB or the JST battery connector then you do not need this connection.
  • Alligator clip leads between P0, P1, P2 on the micro:bit to the Servo for micro:bit board. These need to match up with the servomotors you are using, so if you only need the board for one servomotor, then just connect P0 on the micro:bit to P0 on the Servo for micro:bit and make sure that there is a servomotor attached to the header pins marked 0.
  • Power to the screw terminal on the Servo for micro:bit. Typically this will be a 4xAA battery pack or other power supply. Make sure that the positive lead goes to the screw terminal marked with a +

Test Software

To check that everything is working, this Blocks code project will get you started. Flash it onto your Servo for micro:bit and the servo arms should all start waggling in a random manner. You can see a video of this in action here.

The servo write pin block allows you to set the angle of the servomotor’s arm between 0 and 180 degrees. Note that servomotors, will not usually travel a full 180 degrees so you may find the actual range is more like 10 to 170 degrees.

How We Give Back

We believe in giving back; We are proud to give 1% of all orders directly to environmental not for profit groups whose focus is the protection, preservation and restoration of our planet. This means every time you purchase from us, 1% goes directly to an environmental cause.

Search